Fabrication and Study of The Effect of Flyash On Aluminium 2024 Composite
Keywords:
Composite, Fly ash, Al - 2024, Wear, Hardness, Tensile, MicrostructureAbstract
Al-alloys are widely used application due to their low density, good mechanical properties, better corrosion resistance, wear resistance as compared to conventional metals and alloys. Fly ash is chosen because of it is least expensive and low density reinforcement available in large quantities as solid waste by-product during manufacturing of bricks. Due to low weight it can be utilized in automobile application and thus improving its life. The present work has been done on Al alloy 2024 Fly ash composite. These were fabricated using Al-2024 alloy as metal matrix and fly ash as reinforcing material. Various weight based composites like (Al 100% - FA 0%), (Al 95% - FA 5%), (Al 90% - FA 10%), (Al 85% - FA 15%) were fabricated by Stir casting technique. The obtained composites were sized into small specimens and tests like hardness test, wear test, tensile test, and microstructure test were carried out.
References
- Vinod G. Gokhare, Dr. D. N Raut and Dr. D.K. Shinde: 3D Printing Aspects and Various Processes used in the 3D Printing, In International Journal of Engineering Research & Technology (IJERT), Vol-06, June-2017.
- Ankur Bhargava, Anjani Kumar: Arduino Controlled robotic arm, International Conference on Electronics, Communication and Aerospace Technology (ICECA),2017.
- KruthikaK, KiranKumar B.M and Dr.Sanjay Lakshminarayanan: Design and Development of a Roboticarm.
- Edwin Basil Mathew, Dushyant Khanduja, Bhavya Sapra and Bharat Bhushan: Robotic arm control through Human arm movement detection using Potentiometers, International Conference on recent developments in control, automation and power engineering (RDCAPE),2015.
- Pedro Neto, J. Norberto Pires and A. Paulo Moreira: Accelerometer-based control of an Industrial Robotic arm, The 18th IEEE International Symposium on Robot and Human Interactive Communication,September-2009.
- Virendra Patidar, Apoorva Mishra and Ritu Tiwari: Robotic Gripper Arm System with Effective Working Envelope, International Conference on Intelligent Computing and Control Systems (ICICCS),2018.
- Feng Cao, Jihao Liu, Chen Zhou, Yanzheng Zhao, Zhuang Fu and Weixin Yan: A Novel 5- DOF Welding Robot Based on SCARA, IEEE 10th Conference on Industrial Electronics and Applications (ICIEA),2015.
- Ramish Chouhan, Farah Kanwal, Siraj Ali and Nida Ali: Design and Development of a Prototype Robotic Gripper, International Conference on Robotics and Emerging Allied Technologies in Engineering (iCREATE),April-2014.
- A Guochen, Sha Zhanyou: Programmable Voltage Regulator Design based on Digitally Controlled Potentiometer, International Conference on Electronic Measurement and Instruments (ICEMI),2007.
- Kadirimangalam Jahnavi, Sivraj P: Teaching and Learning Robotic Arm Model, International Conference on Intelligent Computing, Instrumentation and Control Technologies (ICICICT),2017.
- Jeong-WooLeeandTae-WooKim: Designand Experimental Analysis of Embedded Servo Motor Driver for Robot Finger Joints, International Conference on Ubiquitous Robots and Ambient Intelligence (URAI),November-2011.
- Ramesh Kolluru, Kimon P. Valavanis, Stanford A. Smith, and Nikos Tsourveloudis:Design Fundamentals of a Reconfigurable Robotic Gripper System, IEEE TRANSACTIONS ON SYSTEMS, MAN, AND CYBERNETICS, March2000.
- Antonio J. Lopez-Martin and Alfonso Carlosena: Contactless Potentiometers for Automotive Applications, International Conference on Sensing Technology,2013.
- Mohammed Abu Qassem, Iyad Abuhadrous and Hatem Elaydi: Modeling andSimulation of 5 DOF Educational RobotArm.
- Adin Baskoro Pratomo, RizaSatriaPerdana: Arduviz, A Visual Programming IDE for Arduino, International Conference on Data and Software Engineering (ICoDSE),2017.
Downloads
Published
Issue
Section
License
Copyright (c) IJSRCSEIT
This work is licensed under a Creative Commons Attribution 4.0 International License.